|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I AM HIGHLY IMPRESSED BY THE EASE OF USE OF THIS DOWNLOAD SERVICE. INSTRUCTIONS ARE CLEAR AND SIMPLE TO FOLLOW....EVEN BY TECHNOPHOBES SUCH AS MYSELF. THE EMAILS POINT YOU IN THE RIGHT DIRECTION...ITS SO EASY PEASY. THE DOWNLOAD CHOICE OF USER MANUALS IS EXTENSIVE AND I COULD NOT FIND A CHEAPER OR MORE EFFICIENT SERVICE ON THE INTERNET. I COULD NOT HAVE MADE A BETTER CHOICE OF INFORMATION PROVIDER. SHOULD I EVER NEED ANOTHER USER MANUAL, THEN THIS IS THE FIRST CHOICE SITE. COULD NOT BE BETTER PLEASED!!!!!!!...MANY THANXES FROM JIM BURNS
;
I was impressed with the quality of service (frequent e-mails to let you know the status of your order), and the speed at which the download became available. The manual was a life saver and was not easy to track down. Thank you for such an excellent service.
;
the manual was just what i wanted it had all the revelent information required to operate the hifi .Iwould use any manual i downloaded for any item which needs a manual
;
Die gewünschte Bedienungsanleitung wurde vereinbarungsgemäß in deutsch bereitgestellt. Sie ist gut lesbar. Kein Kauderwelsch.
Danke für den Service.
;
GOOD SERVICE MANUAL GOT ALL THE INFO. THAT I NEEDED..
Door reversibility
Remove the two screws which �x the upper hinge to the door. Carefully lean the appliance on its back and remove the plastic insert (Fig. 4).
Fig. 4
Fitting a decorative door panel
Important: The components needed to �t the decorative panel have been pre-�tted on the appliance. The brackets are secured to the panel by means of the 7 � 3.5x13 screws supplied. Before starting to �t the panel, remove the large top bracket by unscrewing the screws and adjusting pins pre-�tted on the appliance door. The small bottom bracket need not be removed. Place the appliance in the position where it is to be built in (Fig. 6). The appliance is �tted with adjustable feet; screw the front and rear feet in or out to adjust the height of the appliance to that of the recess. Keeping the appliance central in the recess, slide it in until its back touches the wall.
D447
Fig. 6
Remove the two screws which �x the lower hinge to the door. Remove the four screws which �x the lower hinge to the base of the appliance and remove the hinge itself; be very careful to recover all the screws. Remove the four screws that �x the upper hinge to the appliance and remove the hinge itself. Take the hinge removed from the upper part of the appliance on the opposite side (see Fig. 5), and, using the screws removed from the lower part, �x it to the base of the appliance itself. Remove and re�t the other hinge on the upper part of the appliance on the opposite side.
Fig. 5
A
= =
With a tape measure (or similar instrument), measu re d i s t a n c e ( A ) between the top edge of the door and the top edge of the decorative panel, placing it next to the recess.
Fig. 7
D467
Lay the panel face down (Fig. 7). Position the top bracket on the panel, making sure that there is an equal distance between it and the sides and
Fix the two front s c re w s i n t o t h e upper and lower hinges (Fig. 5).
=
=
A
-1cm
D510
Finally, check the alignment of the door and make sure it closes properly. After having reversed the opening direction of the door, discard the original plastic insert removed and �t the insert supplied with the appliance on the opposite side.
that its distance from the top edge D468 is equal to distance (A) less 1 cm. Secure the bracket with the screws supplied. Take care not to damage the front face of the panel whilst working.
Fig. 8
B
Insert the adjusting pins (B-Fig. 8) into their locations in the door and screw them in.
D532
6
|
|
|
> |
|
